ARB OME application catalogue

Contents!A1 7. 60043 is 20mm longer and must only be installed to right hand side. 8. OMEB11 bush kit is required to convert lower 19mm bush to 16mm ID. 9. OMESD40 will only fit left hand drive models. 10. 11. No top mounting bushes supplied, re-use OE bushes. Where required, re-use OE Top Hat, Dirt Shield and Bump Stop. 12. 13. No top mounting bushes supplied, refer to vehicle specific application to select relevant upper strut bushes. OE bushes may be re-used if in good condition. 14. FK42 is a mandatory fitment to space sway bar link away from shock absorber. 15. 16. Re-use rear OE top damper forged bracket, bushes, dirt shield, bumpstops and fasteners for the assembly of the rear shock. 17. No top mounting bushes supplied use OME3133 / OME3134 / OME3135, vehicle specific refer to vehicle selection page. OE bushes may be re-used if in good condition. 18. 60130 and 60131 cannot be used as a shock only OE replacement on Colorado 7/Trailblazer Models. Can be used as an OE replacement for Isuzu MU-X. 19. No top mounting bushes supplied use OME3121. OE bushes may be re-used if in good condition. No dirt shield supplied, please re-use OE. 20. Shock absorber 60140 is suited for constant rear loading in excess of 800kgs. 21. 1975 and newer FJ40's may need to use N76 shocks in rear: Pre 1975 shock eye in the top of the axle housing use N89 12 /N95 12 /60032/60064. Post 1975 lower shock eye is below leaf spring use N76 with OMEB11 Bush Kit. 22. FK29 Rear Driveshaft Spacer is a mandatory fitment. 23. Top mount bump stop and bushes not supplied, re-use OE items. 24. For trimming purposes only, maximum 1 packer per strut. 25. OME665 Lower Shock Mount Stone Guard is mandatory fitment to rear shocks to protect against severe stone peppering encountered on loose road surfaces. 26. FK22 Front Shock Absorber Upper Mount Support Bracket Kit is a mandatory fitment. 27. When fitting 60018 / 60070 it is mandatory to fit longer coils 3062 - 3066 for springs to remain trapped with shocks fully extended, fit FK62 to prevent shock damage, fit FK63 for front driveshaft clearance and rear extended travel, fit FK64 which replaces OE upper shock mount when fitting rear shocks and remove any inner helper coils already fitted. Caution: Front driveshaft MUST be replaced / modified with Double Cardan Joints and checked for Uni bind with OME shocks installed at droop. 28. Caution: Due to altered gearbox mounts on models after 1998 any lift above OE ride height may cause front driveline vibration that can only be rectified by fitment of front Double Cardan Joints. 29. Caster Kit will increase caster angle by 2 o . Check manufacturer's specifications to determine if Caster Kit is required. CALR1 suits 38mm wide control arms. CALR2 suits 44mm wide control arms. 30. Volkswagen Service Manual quotes that driveshaft bolts are a one use only. It is recommended to replace bolts. Replacement bolts Volkswagen Part Number N90991102 are to be sourced separately. 31. Suits 75mm and 100mm coils 32. Vehicle specific, refer to vehicle selection page for full details and to review important notification regarding modifications for off road use only along with warranty implications. JK Wrangler: refer page 39 Patrol GU Y61 & GQ Y60: refer page 84 LandCruiser 80 & 105 Serie s: refer page 106 33. For high articulation vehicles it is recommended to replace rear upper shock mount with FK64 and matching shock absorbers 60146 or 60147 34. Fitment of FK92 and FK93 are mandatory . 35. Fitment of LCAJLFR Front Lower Control Arm is required to restore wheel alignment castor settings. 36. To ensure correct 90012 and 90013 strut fitment please refer to fitting instruction part number 3787896 Amarok Strut Fitting Guide. 37. For front fitment reuse OE Top hat and Mounting Bushes. For rear fitment UBolts, Rear Spring Bush Kits and Leaf Spring Bolt Fitting Kit are additional requirements. Extra Leaf, Trim Packer and Centre Bolt are optional. Refer to the vehicle selection page for full details. 38 Headlight Sensor Fitting Kit FK97 is required when fitting all OME extended travel rear shock absorbers. 39 Workshop tool FK102 recommended for rear shock fitment. 40 OME coils and struts can only be installed together due to different winding of the lower coil end to suit the OME coil seat. They are not compatible with the OE coil seat. Due to the nature of the KDSS. Models fitted with KDSS may experience a characteristic 10mm to 15mm lean to the front right hand side. OME struts can only be installed with OME coils. OME front shock 60121 is not suitable as an OE replacement. When fitting our longer OME shock 60121 you must fit: FK71 brakeline kit to extend/drop the brakelines, FK72 sway bar kit to lower the front swaybar, FK70 radius arm drop bracket kit to 11 to 17 models, FK80 to 08 - 10 models as if not fitted you may over stretch the front brakelines. When remaining stock is exhausted no further product will be available. FK16 20mm bump stop spacer kit is a mandatory fitment. NITROCHARGER SPORT SELECTION NOTES: - (cont.) - *first part number has firmer valving. Page 13 OME INT CAT. NO.47 DECEMBER 2021